|
|
|
|
|
|
|
|
|
|
|
These seamless caps keep water off post tops, protecting wood from moisture damage. The PCP's plastic construction is corrosion-proof and paintable.
|
Designed for medium load conditions. Extended 3 in deep seat provides enhanced truss bearing.
|
Designed for reinforcing, attaching, connecting and splicing panels and other home and industrial applications. Product design allows for quick and easy repair of general. household items. Screw holes are countersunk. Boxed loose barcoded.
|
|
|
|
|
|
|
|
|
|
|
|
|
Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2 in less than over center joist spacing. 13 ga.
|
Tamlyn PCS Framing Plywood Clip, Steel, Galvanized, Material Thickness: 20 ga, Maximum Roof Span: 24 in, Number of PC per Spans: 1
|
Tamlyn Framing Plywood Clip, Steel, Galvanized, Material Thickness: 20 ga, Maximum Roof Span: 32, Number of PC per Spans: 1
|
|
|
|
|
|
|
|
|
|
|
|
|
Proper fasteners are a critical component in a sound wood frame structure. To ensure successful installations of its connectors, USP offers a full range of structurally-rated nails. All galvanized nails supplied by USP are hot dipped for greater corrosion resistance. Any USP connector requiring a NA16D-RS or NA20D nail is shipped with the nails attached to the connector in convenient poly bags.
|
Proper fasteners are a critical component in a sound wood frame structure. To ensure successful installations of its connectors, USP offers a full range of structurally-rated nails. All galvanized nails supplied by USP are hot dipped for greater corrosion resistance. Any USP connector requiring a NA16D-RS or NA20D nail is shipped with the nails attached to the connector in convenient poly bags.
|
Designed to anchor wood framing to poured concrete, foundation straps tie mudsill and stud simultaneously to the foundation. Single pour edge installation. G90 galvanized finish. Embedment 10 in. Requires 16d nails for installation. Meets ICC-ES ESR-2787 codes. 10 ge - 24-3/4 in H1 x 10 in H2.
|
|
|
|
|
|
|
|
|
|
|
|
|
Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8 in gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 ga, Boxed.
|
Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2 in less than over center joist spacing. 13 ga.
|
You determine the size. Connect with railing brackets with 2x4 and 2x6 lumber to easily add a bench to any size or shape deck. Gain increased seating area while using only 7 in of deck space. Assembled unit stands 36 in H for deck railing, seat is 17 in H. Quick and easy to assemble using basic tools. Includes bench bracket, hardware and instructions. Lumber not included.
|
|
|
|
|
|
|
|
|
|
|
|
|
Take the work out of fence post installation and repair with the Speedpost, SFP30 and Speedmender, SMP. The speedpost is used to install 4 x 4 fence posts without digging post holes or pouring concrete. The speed mender plates act as reinforcement brackets for rotted or damaged 4 x 4 fence posts.
|
ML angles are multi-purpose angles that install easily with USP's WS15 wood screws. The staggered fastener pattern allows for back-to-back installations.
|
Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2 in less than over center joist spacing. 13 ga.
|
|
|
|
|
|
|
|
|
|
|
|
|
You can determine the size and configuration, just add 2x4's to the ShelfLinks to make functional and custom shelving in any length, height and configuration. Made of structural resin. Can support spans up to 8 ft. Includes ShelfLinks, hardware and instructions. Lumber not included.
|
Coiled strapping enables cut-to-length convenience for a variety of immediate job site needs.
|
Connects wood framing to resist tension forces. G90 galvanizing finish. LSTA light-duty series require 10d nails for installation. Designed for use with 1-1/2 in W framing members, including I-Joist flanges. Meets ICC-ES ESR-1781 codes.
|
|
|
|
|
|
|
|
|
|
|
|
|
G90 galvanizing finish.
|
ML angles are multi-purpose angles that install easily with USP's WS15 wood screws. The staggered fastener pattern allows for back-to-back installations.
|
These anchors tie trusses and rafters to top plates and may be used to tie wood framing members to resist uplift and lateral forces.
|
|
|
|
|
|
|
|
|
|
|
|
|
Connects wood framing to resist tension forces. G90 galvanizing finish. LSTA light-duty series require 10d nails for installation. Designed for use with 1-1/2 in W framing members, including I-Joist flanges. Meets ICC-ES ESR-1781 codes.
|
When using the Grabber Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Grabber Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.
|
When using the Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.
|
|
|
|
|
|
|
|
|
|
|
|
|
When using the Grabber Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Grabber Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.
|
G90 galvanizing finish.
|
These anchors tie trusses and rafters to top plates and may be used to tie wood framing members to resist uplift and lateral forces.
|
|
|
|
|
|
|
|
|
|
|
|
|
Use for joist/header installations. Does not have tabs. G90 galvanizing finish. Requires 8d x 1-1/2 nails. Meets SBCCI, BOCA - NER 505, ICBO 5736, DSA PA-076, Dade County, FL 01-0417.11 and L.A. City RR25303 codes. 18 ga.
|
These anchors tie trusses and rafters to top plates and may be used to tie wood framing members to resist uplift and lateral forces.
|
Tamlyn K-Style Gutter Connector, Carbon Steel, 6-3/8 in L, 7/8 in W
|
|